Jorge Otero, founder of Yacht Masters Hub. Sources checked 14 Nov 2026.
Short answer. Change the oil and filters and stabilize the fuel. Then protect every raw-water circuit aboard — both engines, the generator, each AC pump, and any Seakeeper — by draining it completely or pulling undiluted propylene-glycol antifreeze through until it comes out of the discharge. Check each closed coolant loop against the maker's spec, winterize fresh water and heads, keep batteries charged, and follow your own manuals first.[1][2][5][6]
Why the cooling step matters
BoatUS found that more than three-quarters of ten years of GEICO | BoatU.S. freeze claims involved cracked engine blocks or exhaust manifolds, from water left in the cooling system.[1] Unless you're in Hawaii or the Florida Keys, BoatUS recommends winterizing for a lay-up of even a few weeks.[1]
The checklist
| # | System | What to do | Source |
|---|---|---|---|
| 1 | Fuel | Drain water and contaminants from the tank and fill it to avoid condensation (Volvo Penta); add a diesel stabilizer. | Volvo Penta[2][3] |
| 2 | Oil | Change engine oil and filters and the fuel filters, then run to operating temperature with the seacock open and the impeller in (Volvo Penta does this with the boat still in the water). | BoatUS[1], Volvo Penta[2] |
| 3 | Closed coolant loop | Test freeze protection; use the type and mix your engine maker specifies. | BoatUS[1], Cummins Onan[6] |
| 4 | Raw-water side, each engine | Shut the engine off, then close the seacock. Disconnect the intake hose and put it in a bucket of undiluted non-toxic antifreeze (BoatUS says at least two gallons for an engine and its plumbing; if your engine takes a lot, have a helper keep the bucket topped up). Run until antifreeze comes out of the exhaust for 30 seconds or more. Then shut it off. Or drain every petcock, the strainer, seacock body and water-lift muffler. | BoatUS[1] |
| 5 | Impellers | Leave each impeller in until that engine's or the generator's last run is finished. Then, with it off, remove the raw-water pump impeller and store it in a sealed plastic bag somewhere cool. Do not crank or start it until spring. | Volvo Penta[2], Cummins Onan[6] |
| 6 | Generator | Kohler (diesel marine sets): with the seacock open and the impeller in, run to operating temperature or about 15 minutes, change the oil and filter, shut it off, then close the seacock, disconnect the intake and put the intake hose in about 1–2 U.S. gallons of propylene-glycol mix, and run until it discharges at the exhaust. Then shut it off.[7] Onan: with the seacock open and the impeller in, run under load, change oil, shut it off, then close the seacock, disconnect the intake and put it in the antifreeze bucket, and run until antifreeze discharges. Then shut it off, remove the impeller, and drain the heat exchanger's seawater side and the water-lift muffler. Do not crank or start it until spring.[6] Northern Lights: with the seacock open and the impeller in, run to at least 140°F on stabilized fuel, shut it off, then close the seacock, disconnect the intake and put it in the antifreeze bucket, and run until antifreeze discharges. Then shut it off, loosen the alternator belt, and seal intake and exhaust. Do not crank or start it until spring.[8] | Makers' docs |
| 7 | AC (Dometic Cruisair) | Close the seacock, remove the inlet hose, loosen the pump-head screws to drain, drain and clean the strainer.[9] BoatUS calls pumping non-toxic antifreeze through with the AC pump the better alternative; no need to run the air conditioning itself.[1] | Dometic[9], BoatUS[1] |
| 8 | Seakeeper | Close the seacock, use the display's Seawater Override to purge until undiluted antifreeze comes out of the discharge. | Seakeeper[5] |
| 9 | Fresh water and heads | Use non-toxic propylene glycol here, never ethylene-glycol coolant. Run antifreeze to every outlet; pump out and flush heads. | BoatUS[1] |
| 10 | Batteries | Disconnect, clean and charge: Volvo Penta warns a poorly charged battery can freeze and burst. BoatUS: keep on a marine charger with a float setting, or fully charge at least monthly. | Volvo Penta[2][4], BoatUS[1] |
| 11 | Yard contract | If a yard does it, get a written list of every job and a firm time frame that begins well before the first typical hard freeze; ask your insurer about ice-and-freeze cover. | BoatUS[1] |
Fog the cylinders if the manual says so, on the run with the seacock open and the impeller in. BoatUS's guide gives fogging steps for gasoline engines only.[1] A heater is not a substitute for winterizing.[1]
FAQ
Propylene or ethylene glycol? Propylene glycol for raw-water, drinking-water, head and AC circuits.[1] Ethylene glycol only in a closed loop, if the maker specifies it (Northern Lights does for its gensets).[8]
How much antifreeze for twin diesels? BoatUS says at least two gallons for an engine and its plumbing; if your engine takes a lot, have a helper keep the bucket topped up.[1]
Do I need to winterize in Florida? BoatUS recommends it everywhere except Hawaii and the Florida Keys when laying up.[1]
Should I remove the raw-water impellers? Volvo Penta's IPS manual and Cummins Onan both say to remove them for storage.[2][6]
What does a yard charge? See what it costs to winterize a boat.
Sources
- BoatUS / GEICO-BoatU.S., The Boater's Guide to Winterizing (PDF), undated, retrieved 14 Nov 2026.
- Volvo Penta, Operator's Manual, Volvo Penta IPS, 7747996, 10-2014, "Laying up."
- Volvo Penta UK & IE, "Navigating winter: the importance of winterising your marine engine" (Nov 2023).
- Volvo Penta, Operator's Manual D4/D6, 47716267, 05-2026.
- Seakeeper, "How do I winterize my Seakeeper?", undated, retrieved 14 Nov 2026.
- Cummins, "Onan Marine Generator Maintenance", undated, retrieved 14 Nov 2026.
- Kohler, Operation manuals TP-6772 3/19e §3.9 and TP-7044 6/23e §3.12, Generator Storage Procedure (diesel marine sets).
- Northern Lights, "Tips for Winterizing Your Generator", undated, retrieved 14 Nov 2026.
- Dometic, Cruisair DX remote/self-contained manual, "Winterizing the System", ©2004, retrieved 14 Nov 2026.