How to dewinterize a boat with inboard diesels and a generator

Jorge Otero, founder of Yacht Masters Hub. Sources checked 14 Nov 2026.

Short answer. Ashore: reinstall or replace each raw-water impeller, drain antifreeze from the seawater side where your manual says to, close the drain plugs, check belts, hoses, clamps, oil and coolant, and charge the batteries. Check props, shaft play, stuffing boxes, seacocks and anodes. After launch, check every thru-hull for leaks, then start each engine and the generator and look for fuel, coolant and exhaust leaks.[1][2][4]

The checklist

# Step What to do Source
1 Oil Check engine and drive oil. If inhibiting oil was used, drain, refill and change the filter. Volvo Penta[2]
2 Seawater side Drain the antifreeze from the seawater system. Close or tighten all drain cocks and plugs (on the genset: muffler and heat-exchanger drain plugs). Volvo Penta[2], Cummins Onan[4]
3 Impellers Install the impeller in each seawater pump; replace it if it looks worn. Cummins Onan: replace a genset impeller over one year old. Volvo Penta[2], Cummins Onan[5]
4 Belts, hoses, clamps Check belt tension and condition; check rubber hoses for stiffness, rot, leaks or cracking. BoatUS: double-clamp fuel lines, exhaust hoses and, if possible, hoses below the waterline. Volvo Penta[2], BoatUS[1]
5 Coolant Check coolant level and antifreeze protection; top up. Volvo Penta[2]
6 Fuel Inspect fuel lines, tanks, pumps and filters for leaks. Onan: replace the genset's primary and secondary fuel filters. BoatUS[1], Cummins Onan[4]
7 Exhaust Every few years, remove and inspect exhaust manifolds and risers for corrosion. BoatUS[1]
8 Batteries Charge, clean and tighten connections; connect fully charged batteries. BoatUS[1], Volvo Penta[2]
9 Running gear Inspect props for dings, pitting and distortion. Grip the prop and try to move the shaft; if it wiggles, the cutless bearing may need replacing. Check the rudder bearing for play. BoatUS[1]
10 Stuffing boxes Should leak "no more than two or three drops each minute when the prop shaft is turning." BoatUS[1]
11 Seacocks and strainers Inspect, lubricate and exercise seacocks. Check the sea strainer isn't cracked or bent from ice. BoatUS[1]
12 Anodes On Volvo Penta drives, replace an anode with less than two-thirds left; clean with emery cloth just before launch, not a wire brush. Volvo Penta[2][3]
13 Launch Check all thru-hulls for leaks. Start each engine; check for fuel, coolant and exhaust leaks and that all controls work. BoatUS[1], Volvo Penta[2]
14 Generator Open the thru-hull valves, start and run it, check for leaks and odd noises, start and stop from every station, check frequency. Cummins Onan[4]
15 Alarms and safety Run the bilge blower, test engine warnings and alarms, the bilge pump and float switch, and smoke, CO and fume alarms. BoatUS[1]

FAQ

Do I drain the antifreeze from the engine? From the seawater (raw-water) side, Volvo Penta says yes. The closed coolant loop stays; check its level and protection.[2]

Should I replace the impellers every spring? Volvo Penta says replace if worn. Cummins Onan says replace a generator impeller over a year old.[2][5]

How much should a stuffing box drip? BoatUS: no more than two or three drops a minute with the shaft turning.[1]

When should I change anodes? Volvo Penta drives: replace one with less than two-thirds left. BoatUS's outdrive section says replace any more than half wasted. Follow your own maker.[1][2]

Sources

  1. BoatUS, Spring Commissioning Checklist (2022/v3, PDF).
  2. Volvo Penta, Operator's Manual, Volvo Penta IPS, 7747996, 10-2014, "Bringing out of storage."
  3. Volvo Penta, Operator's Manual D4/D6, 47716267, 05-2026.
  4. Cummins, "Onan Marine Generator Maintenance" ("When returning the generator set to service"), undated, retrieved 14 Nov 2026.
  5. Cummins Onan, Operator Manual MDKBJ/MDKBW, A029Z105 Issue 5, §5.9.